Effects of extended mixing processes on fresh, hardened and durable properties of cement systems incorporating fly ash

Scientific Reports volume 13, Article number: 6091 (2023) Cite this article 972 Accesses 3 Citations Metrics details Specifications that correspond with system performance may guarantee the addition

Scientific Reports volume 13, Article number: 6091 (2023) Cite this article

972 Accesses

3 Citations

Metrics details

Specifications that correspond with system performance may guarantee the addition of value. Most specifications for ready-mixed concrete address limits on discharge time and truck-drum revolution counts. These limits have been developed for conventional concrete. As the uses of supplementary cementing materials (SCMs) become ubiquitous, it is important to determine whether these specifications are applicable to SCMs, that is, systems containing fly ash. This paper presents results of the effects of mixing time and mixer revolution counts on characteristics of lab-made pastes and mortars containing 20% and 50% fly ash. Their characteristics assessed include time-variant ion concentrations, setting time, flow, compressive strength, porosity, and apparent chloride diffusivity coefficient. Results indicate that with increasing mixing time and mixer revolution counts, mixtures with a replacement of fly ash exhibit improved both fresh and hardened characteristics. When mixed for 60 min or 25,505 revolution count, the 28-day compressive strengths of mixtures containing 20% and 50% fly ash are 50% to 100% higher than the neat cement. Fly ash is suggested to adopt in the extended mixing processes of cement systems.

Fly ash is a pozzolanic byproduct of the coal combustion process used to generate electricity. Currently, the coal combustion process accounts for roughly 50 to 55% of the United States' total energy generation1,2. Approximately 75 percent of the byproducts of this operation are fly ash3,4,5. Consequently, it is predicted that 500–550 million tons of fly ash are produced annually on a global scale6,7. Many sectors employ fly ash, including the agricultural and cement and concrete industries. It has been found that employing fly ash in the cement and concrete industries improves the performance characteristics of the hydrated products8,9. The main use of fly ash for the production of modern concrete composites, leading to new innovative solutions in this field, such as nano materials10, quaternary and ternary binders11,12,13, and active seeds14,15. The new innovative solutions can offer customized concrete products for various applications. However, more than 70 percent of the fly ash collected from power plants is not used, which poses a severe disposal challenge16,17. Coal-fired power facilities incur extra expenditures due to the disposal of fly ash. The annual cost is expected to be roughly $1.2 billion18. Therefore, more research and innovations that may expand the use of fly ash are necessary, particularly in the cement and concrete sectors. In addition to lowering disposal costs, this may enhance the performance characteristics of concrete mixes.

Concrete is the second most frequently utilized substance in the world, after water19. There have been significant efforts to limit CO2 emissions from the cement and concrete sectors due to environmental concerns. Nevertheless, the CO2 emissions from these businesses remain notably high, and more efforts are required. American Coal Ash Association (ACAA)20 calculated that using fly ash as a source of supplemental cementing material (SCM) in concrete can save CO2 emissions by 10 to 14 tons/year in the U.S. alone. Not only can the partial replacement of fly ash promote sustainability by lowering CO2 emissions, but it also decreases the expenses associated with producing concrete and disposing of fly ash. The Federal Highway Administration (FHWA) rules encourage concrete systems containing fly ash. This is especially true when the price of fly ash concrete is comparable to or lower than that of portland cement concrete (PCC)21. Hence, not all cement should be replaced with fly ash in a given mix. In addition to environmental and economic benefits, it is recognised that substituting Portland cement (PC) with fly ash improves the fresh properties and hardened performance of the hydrated product. As a pozzolanic material, calcium hydroxide (Ca(OH2)) may be reacted to produce calcium silicate hydrates that increase strength (C-S–H). These hydrates result in a densified interfacial transition zone (ITZ) and improved concrete microstructures at the interface of cement paste and aggregates22,23. Consequently, the performance of concrete systems incorporating fly ash may be superior to that of conventional concrete systems, and this may include ready-mixed concrete.

Ready-mixed concrete is defined by the American Society for Testing and Materials (ASTM) as concrete that is made and delivered to a client in a fresh state. Specifications for ready-mixed concrete from the American Association of State Highway and Transportation Officials (AASHTO), the American Concrete Institute (ACI), ASTM, and/or the State Highway Agencies (SHAs) address discharge time, truck-drum rotations, and/or concrete temperature limitations. In the United States, 48 of 50 SHAs restrict the duration before discharge to between 45 and 120 min; 30 of 50 SHAs limit the number of truck drum spins to between 250 and 320; and 45 of 50 SHAs limit the concrete temperature to between 28 and 38 °C. Because increasing discharge duration and number of drum revolutions might affect the workability of new cement and concrete mixes24,25, the majority of SHAs restrict these factors. Reduced workability makes it difficult to consolidate a new concrete. Improper placement and consolidation can lead to large voids, honeycombing, and increased permeability in hardened concrete26,27,28, resulting in a considerable decrease in compressive strength and durability. According to Anderson and Hodson29, the cost of polishing the hardened surface after casting is complete is about two to five times the cost of concrete's raw materials. Improved workability of fresh concrete can reduce placement efforts, resulting in lower construction expenses.

According to the Portland Cement Association (PCA)30, more than fifty percent of ready-mixed concrete contains fly ash. In infrastructure systems, fly ash-containing concretes are omnipresent. Although numerous research has evaluated the impacts of mixing factors on the performance of PCC, few studies have evaluated the effects of mixing variables on the performance characteristics of fly-ash-containing concrete.

Moreover, because PCC and concretes containing fly ash use the same limits of mixing time (i.e. 45 to 120 min) and total drum revolutions (i.e. 250 to 320 revolutions), contractors are questioning whether these current limits are still applicable to concretes containing fly ash and, if not, whether they should be modified. It is essential that the limit requirements adjust to new developments in materials and building processes, allowing for the addition of value. In addition, Hooton31 stated that limit requirements had to be changed to performance-based specifications so as not to restrict the development of alternative systems (e.g., systems containing fly ash). Before determining these difficulties, it is necessary to have a better knowledge of the performance characteristics of cementitious systems incorporating fly ash.

This research describes the laboratory assessment of the effects of mixing time and mixer revolution counts on the fresh and hardened properties of PC pastes and mortars containing 20% and 50% fly ash by weight. This research evaluates the time-dependent concentrations of hydroxyl, calcium, and aluminate ions in solution, the setting time of pastes, and the flowability of new mortars. The 1-, 7-, and 28-day compressive strengths (fc), 28-day porosity, and apparent chloride diffusion coefficient (Da) are tested as hardened properties of cement mortars.

Type I PC was obtained from SCG, Thailand and used for all mixtures in this research. Class-F fly ash per ASTM C618 was procured from a local powerplant. The X-ray diffraction (XRD) chemical composition of PC and fly ash is shown in Table 1. A Scanning Electron Microscopy (SEM) image of fly ash particles is shown in Fig. 1. The particles of fly ash that were seen have a spherical form, a smooth surface, and a wide range of particle size distribution. Standard graded sand meeting ASTM C778 was used for the flowability, 28-day porosity, and Da specimens. Type II de-ionized (DI) water (1 MΩ·cm at 25 °C) was used for all mixtures and experiments. Fine aggregate, used for the fc specimens, was procured from a local source in Saraburi, Thailand and met the requirements of ASTM C33. The fineness modulus of the fine aggregate was 3.1 determined following ASTM C136. The specific gravity of the fine aggregate was 2.47 and the absorption was 3.08%. The specific gravity and absorption values were determined following ASTM C128.

SEM micrograph of fly ash particles.

The cement pastes and mortars were mixed in accordance with ASTM C305. The fly ash systems were prepared by substituting fly ash for cement by weight. A control combination (100% PC) was formulated and evaluated for comparison. The water-binder ratio (w/b) of the paste sample was 0.40. The specimens of mortar were made using a w/b ratio of 0.48 and a cement-fine aggregate ratio of 1.27:1. The C305 standard mandates two stages of mixing for pastes and mortars: low speed mixing (140 rpm) followed by intermediate speed mixing (250 and 285 rpm). Only the second stage's mixing time and speed were modified throughout this study. The mixing techniques for cement pastes and mortars are detailed in Table 2. Four mixing durations (2, 15, 60, and 90 min) and two mixing speeds (140 and 285 rpm) were investigated. This resulted in 210, 355, 2030, 4060, 8330, 12,600, 16,885, and 25,578 revolution counts for paste mixing and 350, 568, 2170, 4273, 8330, 12,600, 17,098, and 25,505 revolution counts for mortar mixing. All test results are based on triplicate tests.

The time-variant hydroxyl ion concentrations in solution at early ages were evaluated using a pH electrode. The w/b value of the solutions was 4.0. Mixing for all systems was performed using a magnetic stirrer rotating at 0 and 400 rpm throughout the mixing period. Mixing at 0 rpm means the cement samples were manual mixed with water until they are uniform and then left without additional agitation. The time elapsed after introducing the unhydrated PC to the solution is referred to here as the “hydration time.” Solutions used for evaluating hydroxyl ion concentrations were analysed at 5, 10, 15, 30, 45, 60, 90, 120, 150, 180, 210, and 240 min (mixed at 0 and 400 rpm).

Using flame atomic absorption spectroscopy (FAAS), the amounts of aluminate and calcium ions were calculated. The process for determining hydroxyl ion concentrations was followed by mixing. At the same hydration durations as the studies of hydroxyl ion concentrations, solutions were evaluated at 300, 360, and 420 min of further hydration time.

At each hydration time, test solution (30 ml) was decanted from the mixing beaker and filtered using a vacuum pump and No. 40 filter paper. Ten ml of filtered solution was used for analysing aluminate ion concentrations and 1 ml of filtered solution was used for analysing calcium ion concentrations. Because high concentrations of calcium ions occur at early ages, filtered solutions for analysing calcium ion concentrations were diluted prior to the FAAS analyses. Filtered solutions for determining calcium ion concentrations were diluted with 9 ml of DI water to obtain the solution within the detection range of the FAAS. After decanting and diluting, 1 ml of lanthanum acid solution [50 g/l lanthanum oxide (La2O3) in 3 M hydrochloric acid (HCl)] was added to the solutions for the FAAS analyses. Concentrations of aluminate ions were determined using the FAAS with nitrous oxide-acetylene gas at a wavelength of 309.3 nm ignited at the temperature of 2600 to 2800˚C. The calcium concentrations were determined using air-acetylene gas at a wavelength of 422.7 nm ignited at the temperature of 2100 to 2400 ˚C. A blank sample (DI water only) was also analysed and used as a background correction.

Following ASTM C1437, the flowability of new mortars was evaluated. The setting time of cement pastes was evaluated using the ASTM C191 standard. Following ASTM C109, the 1-, 7-, and 28-day fc values were established. After casting, test specimens were stored for 24 h in plastic molds before being demolded. Before testing, deformed specimens were treated in a saturated lime solution. The 28-day porosity of mortars was measured using a modified ASTM C642 technique. Prasittisopin and Trejo28 detail methods for the modified porosity test. The Da was calculated using ASTM C1556. After casting cylindrical mortar specimens measuring 75 mm by 150 mm to determine the Da, the specimens were stored in plastic molds for 24 h before being demolded. The specimens were subsequently subjected to a chloride solution for 35 days after being cured in saturated lime solution for 28 days. Specimens of powder were examined for chloride ion concentration in accordance with ASTM C1152. For testing chloride ion concentration, a computer-controlled potentiometric auto-titrator with a sample changer was utilised. After calculating the chloride ion concentration at various depths below the surface, the Da was calculated using Fick's second rule, as indicated in Eq. 1.

where $C(x,t)$ is percent chloride ion concentration at depth x and exposed time t; Cs is predicted percent chloride ion concentration at the surface of the exposed mortar; Ci is percent initial chloride ion concentration of specimens before solution exposure; and erf is the error function.

To compare sample means with two groups and more than two groups, respectively, the two-sample t-test and analysis of variances (ANOVA) were utilised. Before the analysis, the Shapiro–Wilk test was used to determine whether the data had a normal distribution, and the Levene’s test was used to investigate whether the data had an equal variance. The following statistical hypotheses were defined as:

The 95% confidence intervals were used for all analyses. If the H0 is rejected (p-value ≤ 0.05), it is concluded that there is statistically significant difference at the 5% level between the means of group populations. Alternatively, if the H0 is not rejected (p-value > 0.05), it is concluded that there is no statistically significant difference at the 5% level between the means of group populations.

This section entails six experimental investigations including (1) ion concentration of hydroxyl, aluminate, and calcium, (2) flowability of fresh mixtures, (3) initial setting time, (4) compressive strengths at different curing times, (5) 28-d porosity, and (6) Da.

The effect of hydration time on the hydroxyl ion concentrations for the control, 20%, and 50% fly ash systems mixed at 0 and 400 rpm is shown Fig. 2a,b, respectively. Results indicate that the hydroxyl ion concentrations of all systems increase when hydration time increases. The slope of the fitted curve is referred to as the dissolution rate of the hydroxyl ions in solution. Larger slope indicates higher dissolution rate of hydroxyl ions in solution.

Effect of hydration time on hydroxyl ion concentration mixed at (a) 0 rpm and (b) 400 rpm of control system and systems containing 20% and 50% fly ash.

In Fig. 2a, the slopes of the control, 20%, and 50% fly ash systems are 9.0, 7.7, and 5.2 mmol/l/min, respectively. The larger slope of the control system corresponds with higher rate of dissolution of hydroxyl ions than the 20% and 50% fly ash systems. Increased percent replacement level of fly ash in the cementitious systems has been reported to result in decreased hydroxyl ion concentration in solution32. This is believed to occur because fly ash acts as “inert.” Hence, the fly ash mixtures contain less cement. Results in Fig. 2b are similar with the results in Fig. 2a, of which the slope of the control system mixed at 400 rpm (17 mmol/l/min) is larger than the slopes of the 20% (15 mmol/l/min), 50% fly ash (13 mmol/l/min) systems mixed at 400 rpm. Increased replacement level of fly ash results in decreased dissolution rates of hydroxyl ions, irrespective of mixing speed.

Comparing the results in Fig. 2b with the results in Fig. 2a indicates that the slopes of the control, 20%, and 50% fly ash systems mixed at 400 rpm are approximately 89%, 95%, and 150% higher than the slopes of the control, 20%, and 50% fly ash systems mixed at 0 rpm, respectively. The steeper slope is attributed to faster rate of dissolution of hydroxyl ions. This indicates that mixing speed strongly affects the dissolution rate of hydroxyl ions of all systems and could affect early-age characteristics of mixtures (as discussed later). Mixing speed increasingly affects the dissolution rate of hydroxyl ions in the systems containing higher replacement levels of fly ash.

Figure 3a shows the time-variant concentrations of aluminate ions of the control, 20%, and 50% fly ash systems mixed at 0 rpm. Results indicate that the aluminate ion concentrations of the control system are lower than the aluminate ion concentrations of the 20% and 50% fly ash systems. The plot of aluminate ion concentrations of the control, 20%, and 50% fly ash systems mixed at 400 rpm as a function of the hydration time is shown in Fig. 3b. Like the results of all systems mixed at 0 rpm in Fig. 3a, the aluminate ion concentrations of the control system are lower than the 20% and 50% fly ash systems. More importantly, the aluminate ion concentrations mixed at 400 rpm for all systems are not stable, when compared with the aluminate ion concentrations in solutions mixed at 0 rpm. This “unstable” state likely occurs due to mixing speed. Because the aluminate ion concentrations are not stable in the systems mixed at 400 rpm, it is expected that there would be the differences of early-age characteristics (e.g., setting) between the systems that are continuously mixed and the systems that are mixed and then stop mixing.

Effect of hydration time on aluminate ion concentration mixed at (a) 0 rpm and (b) 400 rpm of control system and systems containing 20% and 50% fly ash.

The effect of hydration time on the calcium ion concentrations for the control, 20%, and 50% fly ash systems mixed at 0 and 400 rpm is shown Fig. 4a,b, respectively. Results in both figures indicate that the control systems mixed at 0 and 400 rpm have higher calcium ion concentrations than the 20% and 50% fly ash systems. The presence of fly ash results in reduced calcium ion concentrations at early ages due to less cement contents. In addition, these lower calcium ion concentrations could be a result of fly ash particles acting as nuclei for lime precipitation. Lawrence33 and Fraay et al.34 reported that the lime precipitation can occur when replacing cement with SCMs. Like the results of the aluminate ion concentrations in solutions mixed at different speeds (shown in Fig. 3a,b), the calcium ion concentrations in solutions mixed at 400 rpm are not stable compared to the solutions mixed at 0 rpm. Apparently, results from the aluminate and calcium ion concentrations indicate that when mixing continuously progresses, ions are likely unstable, thereby affecting other early-age characteristics.

Effect of hydration time on calcium ion concentration mixed at (a) 0 rpm and (b) 400 rpm of control system and systems containing 20% and 50% fly ash.

Table 3 summarises the effects of the replacement of fly ash in cementitious systems on the concentrations of hydroxyl, aluminate, silicate, and calcium ions in solutions at early ages. Regarding the ion concentration studies for extended mixing processes, replacing cement with fly ash can lead to (1) decreased hydroxyl ion concentration due to less cement contents, (2) increased aluminate ion concentration due to a formation of aluminate-rich gel layers, (3) increased silicate ion concentration due to more silicon from fly ash in cementitious systems, and (4) decreased calcium ion concentration due to lime precipitation and less cement content35,36.

The effect of mixing time on normalised flowability of the control, 20%, and 50% fly ash systems mixed at 285 rpm is shown in Fig. 5a. The flow values are normalised with the maximum flow values (183 mm) of the 50% fly ash systems. Results indicate that a flow reduction of all systems is a result of increased mixing time. The flow of the fresh mortars of the 20% and 50% fly ash systems mixed for 2 min exhibits approximately 12% and 31% larger flow than the control system, respectively. The flow of the fresh mortars of the 20% and 50% fly ash systems mixed for 15 min exhibits approximately 30% and 48% larger flow than the control system, respectively. Lastly, the flow of the fresh mortars of the 20% and 50% fly ash systems mixed for 60 min exhibits approximately 50% and 43% larger flow than the control system, respectively. It is noted that the flowability in the figures has been tested at 285 rpm only. The lower mixing speed (140 rpm) was conducted for calculating different mixer revolution counts. Bentz and Ferraris37 reported that as hydrating products form, the early stiffening behavior is controlled by the gradual loss of free water from hydration reactions.

Effect of (a) mixing time and (b) mixer revolution counts on normalized flow of control system and systems containing 20% and 50% fly ash.

Paya et al.38 reported that flow of cementitious systems containing fly ash is influenced by several factors such as size distribution, morphology, surface condition, fineness, and loss on ignition of the fly ash particles. Replacing cement with fly ash is believed to make more water available for flow. Gopalan39 reported the water absorption characteristics of the cementitious systems are reduced when fly ash is present. In addition, the spherical particles and better particle size distribution of fly ash (which is shown in Fig. 1) lead to the reduction in friction between constituent particles in the systems (this commonly known as the “ball-ability” or “ball-bearing effect”)40,41. Thus, although increased mixing time results in reduced flow of the fly ash systems, the fresh mixtures can be mixed longer and still be castable due to improved flow.

The plot of the normalised flow of the control, 20%, and 50% fly ash systems as a function of mixer revolution counts is shown in Fig. 5b. Results indicate the flow of all systems significantly reduces with increasing mixer revolution counts. The control system has less flow than the 20% and 50% fly ash systems. Replacing cement with fly ash results in a significant increase in flow of the fresh mixture and that allows proper consolidation process of mixtures mixed at higher mixer revolution counts can be performed. Based on test data, specification’s limits on mixing time and mixer revolution counts may not be appropriated when fly ash is present in the cementitious systems.

Figure 6a shows the effect of mixing time on the initial setting time of the control, 20%, and 50% fly ash systems. Results indicate that increased percent replacement level of fly ash results in delayed initial setting times. Possible reasons of delaying effect is likely due to the adsorption of calcium ions on the surface of fly ash42 and lowered hydroxyl ion concentrations. These lead to delayed nucleation and precipitation process of the Ca(OH)2, C-S–H, and ettringite. Results also indicate that increased mixing time leads to increased initial setting time of the control and 20% fly ash systems (ANOVA test with p-value < 0.05). This is likely because the ions in the systems are in the unstable state (as discussed) and the constituent’s particles are still deformed by a movement of mixing tools during continued mixing. This deformation of the particles likely disturbs the adhesion bonding of hydrating particles to form a larger structure. Hence, during mixing, the hydrating particles lose their load-supporting ability, consequently resulting in slower setting. After mixing discontinues, the adhesion bonding begins to form a larger structure and this structure, with time, begins to support external loads. However, it is assumed that part of water is consumed by hydration reactions during extended mixing since the hydration reactions can generate substantial amount of heat, and this heat of hydration leads to increased water evolution rate. Hence, less amount of water available for flow before casting and consolidating the specimens. This less amount of water of mixtures finally results in increased energy to cast and consolidate the specimens28. The hardened specimens seem to have higher void volume and larger void size. Voids in hardened cement systems generally results in lower fc and finally leads to deteriorate the durability and shorten serviceability. The porosity will be discussed later in Section "Compressive strength". It should be noted, however, that this work was done in paste and mortar systems while conducting research on either expanding the mix volume for the ready-mix concrete truck for each region or switching to concrete systems is mandatory.

Effect of (a) mixing time and (b) mixer revolution counts on initial setting time of control system and systems containing 20% and 50% fly ash.

Figure 6b show the effect of the initial setting time as a function of mixer revolution counts of the control, 20%, and 50% fly ash systems. According to the findings, it appears that the initial setting time tends to prolong as a function of the number of mixer revolutions. The initial setting times of cementitious systems containing fly ash are delayed as a result of increased mixing times as well as increased mixer revolution counts.

Figure 7a,b show the 1-day fc of the control, 20%, and 50% fly ash systems as a function of mixing time and mixer revolution counts, respectively. Results indicate that increased percent replacement level of fly ash leads to lower 1-day compressive strength. Statistical analyses indicate that the 1-day fc of all systems is not influenced by mixing time and mixer revolution counts (ANOVA test with p-value > 0.05).

Effect of (a) mixing time and (b) mixer revolution counts on 1-day fc; (c) mixing time and (d) mixer revolution counts on 7-day fc; (e) mixing time and (f) mixer revolution counts on 28-day fc of control system and systems containing 20% and 50% fly ash.

Figure 7c,d show the effect of mixing time and mixer revolution counts on the 7-day fc for the control system and systems containing 20% and 50% fly ash, respectively. Results indicate that the 7-day fc of all systems is not significant affected by mixing time (ANOVA p-value > 0.05). In addition, the 7-day fc of the control systems does not have a significant effect by mixing time (ANOVA p-value > 0.05); however, the 7-day fc of the 20% and 50% fly ash does (ANOVA p-value < 0.05).

The effects of mixing time and mixer revolution counts on the 28-day fc of the control, 20%, and 50% fly ash systems are shown in Fig. 7e,f, respectively. Similarly with the results of the 1- and 7-day fc, results indicate that mixing time does not a significant effect on 28-day fc of all systems. In summary, extended mixing time does not influence on both early- and later-age fc. Regarding the compressive strength of ready-mixed concrete systems, their current discharge time limits as specified in many SHAs seem impractical use. However, here, the mixer revolution counts do influence 28-day fc. Increased mixer revolution counts result in a reduction of 28-day fc of the control system but result in an increase of 28-day fc of the systems containing fly ash. It has been reported that an increase in the consolidation energy consumption is responsible for the 28-day fc drop that occurs as a function of the number of revolutions of the mixer28. The fc will begin to decrease as soon as the energy available is insufficient to consolidate the specimens. The voids of cement systems enlarge and increase. As aforementioned, larger voids and greater void volumes of cement systems likely lead to reduced fc and consequently lead to shorten their service life. When considering the revolution count, results apparently exhibit the SHAs’ limits should be in place. These can ensure the ready-mixed concrete can deliver to the users in good conditions. However, the systems that contain fly ash show an increase in 28-day fc, and it is assumed that this is because there is less water in their mixtures (which results in a lower w/b value). Increased rates of water evaporation and hydration reactions were claimed to be the cause of less water being present in the mixtures by Dewar and Anderson43.

Results herein indicate that mixing time does not have a significant influence on 1-, 7-, and 28-day fc. The summary of the influence of mixer revolution counts on the fc of the control, 20%, and 50% fly ash systems is shown in Table 4. The early-age fc values (1- and 7-day) do not have a significant impact by increasing the mixer revolution counts. On the other hand, the 28-day fc will decrease for the control system as the number of mixer revolutions increases, but it will rise for the systems that include fly ash. Under the extended mixing conditions, the presence of fly ash in cementitious systems can improve the long-term compressive strength. Hence, the ready-mix concrete products should partially contain fly ash especially when a long haul is needed. As discussed before, the SHAs’ limits on discharge time and mixer revolution counts of ready-mixed concrete seems to require a revision when fly ash is present. In the revised versions, it is recommended that the longer discharge time and greater revolution count can be addressed, and this can be beneficial to the all stakeholders in ready-mixed concrete chain. The ready-mixed concrete producers can easily plan for various logistic routes and schedules. The consumers can receive a good quality of resulting concrete products. Finally, waste generated from over-limited ready-mixed concrete can be decreased that ultimately offer more cost effective and more sustainable manners to the industry44.

The effects of mixing time and mixer revolution counts on the 28-day porosity of the control, 20%, and 50% fly ash systems are shown in Fig. 8a,b, respectively. Results indicate that increased mixing time does not significantly affect the 28-day porosity for all systems (ANOVA p-value > 0.05). Results also reveal that significant increase in porosity should only relate to the control mix. Increased percent replacement level of fly ash results in higher porosity. Figure 8b shows that increasing the mixer revolution counts at lower revolutions (less than approximately 3000) results in a significant increase in porosity (ANOVA test with p-value = 0.013). However, increasing the mixer revolution counts at higher revolution counts (more than approximately 3000) has less influence on the porosity of mixtures (ANOVA test p-value > 0.05). The porosity of the systems containing fly ash does not exhibit this effect like the control system.

Effect of (a) mixing time and (b) mixer revolution counts on 28-day porosity of control system and systems containing 20% and 50% fly ash.

Figure 9 shows the correlation between the normalised 28-day compressive strength and the 28-day hardened porosity of the control, 20%, and 50% fly ash systems for different mixer revolution counts. The 28-day fc values are normalised with the mean 28-day fc for all mixtures. The linear fitted curve was illustrated in this study. The logarithmic fitted curve shown is reported by Neveille45 and the exponential and linear fitted curves are reported by Brandt46. Although different type of the fitted curve is not similar with the curves from previous studies, the linear fitted curve in this study is not distinguished from others. Results indicate that the 28-day fc is reduced with increasing porosity and this increased porosity is likely due to reduced flow caused by higher mixer revolution counts. It is assumed that the primary criteria reflecting the overall performance of macrostructures are parameters relating to the adequate flow of fresh cement mixtures resulting from extended mixing.

Relationship between normalized 28-day fc and 28-day porosity of control systems and systems containing 20% and 50% fly ash mixed at different mixer revolution counts.

Figure 10a,b show the effects of mixing time and mixer revolution counts on the Da of the control, 20%, and 50% fly ash systems, respectively. Results indicate that neither mixing time nor mixer revolution counts has a significant effect on the Da for all systems (ANOVA p-value > 0.05). The control system exhibits higher Da than the systems containing fly ash (ANOVA p-value = 0.026). Consequently, only the influence of material components influences corrosion resistance, not mixing activities. It is common knowledge that adding fly ash to cement systems can result in a denser microstructure and reduced porosity at later ages. This is because pozzolanic reactions (reaction between CaO and S to form C-S–H products) progress at later ages47,48. Golewski47 mentioned that the homogenous and uniform structure of the portland cement system containing FA was seen after 14-day curing period, which resulted from the transformation of disordered phases into compact and homogenous forms and the filling of porous voids of C-S–H phase. Sabet et al.49 reported that the presence of fly ash in the cementitious systems can react with Ca(OH)2 to produce C-S–H products and also bind chloride ions by the aluminate phases during chloride exposed period. These lead to reduced transport rates, and finally the service life of concrete structure can be extended.

Effect of (a) mixing time and (b) mixer revolution counts on Da of control system and systems containing 20% and 50% fly ash.

This study assessed the influence of extended mixing processes on the performance parameters of cementitious systems including fly ash. At various mixing periods and mixing speeds, the dissolution kinetics of hydroxyl, calcium, and aluminate ions were examined. At various mixing periods and mixing revolution counts, the fresh and hardened characteristics of pastes and mortars were examined. The findings suggested that:

Increased mixing speed resulted in increased dissolution kinetics of hydroxyl ion in solutions and made calcium and aluminate ions stay in the unstable state.

Increased replacement level of fly ash leads to increased flow values but slower setting time. Thus, while longer mixing processes lower the flow values, fly ash mixes can be castable due to better flow.

With increasing mixer revolution counts, the 28-day fc of systems with no fly ash reduce but the 28-day fc of the systems with fly ash increase.

The porosity of the fly ash mortars does not influenced by mixing time and mixer revolution counts.

The Da is not affected by these mixing time and mixer revolution counts. However, when fly ash presents, the Da can be affected by these mixing time and mixer revolution counts.

Existing requirements from the majority of SHAs may not be relevant to cementitious systems including fly ash, based on the study's findings about mixing time and mixer revolution counts. Ongoing research examines the influence of these present constraints on the performance qualities of concrete containing fly ash.

The datasets used and/or analysed during the current study available from the corresponding author on reasonable request.

U.S. Department of Energy. Coal. 2011.

Stewart, B. Current trends in coal combustion products (ccps) production and use. 5th Intern Pittsburgh Coal Conf. Pittsburgh 1998. p. 263–71.

Mahlaba, J., Kearley, E. P. & Kruger, R. A. Microstructural and mineralogical transformation of hydraulically disposed fly ash-implications to the environment. Coal Combust. Gasfi. Prod. 4, 21–27 (2012).

Google Scholar

Haynes, R. J. Reclamation and revegetation of fly ash disposal sites—Challenges and research needs. J. Environ. Manag. 90(1), 43–53 (2009).

Article CAS Google Scholar

Jala, S. & Goyal, D. Fly ash as a soil ameliorant for improving crop production—A review. Bioresour. Tech. 97, 1136–1147 (2006).

Article CAS Google Scholar

Acar, I. & Atalay, M. U. Characterization of sintered class F fly ashes. Fuel. In press.

Twardowska, I. & Szczepanska, J. Coal combustion waste. Solid Waste: Assess Monitor and Remed. 2004:387–452.

Massazza, F. Pozzolana and pozzolanic cements. In Lea’s Chemistry of Cement and Concrete 4th edn (ed. Hewlett, P. C.) 471–635 (Butterworth-Heinemann, 2008).

Google Scholar

Mehta, P. K. & Monteiro, P. J. M. Concrete: Structure, Properties, and Materials 3rd edn. (McGraw-Hill, 2006).

Google Scholar

Zhang, P., Han, S., Golewski, G. L. & Wang, X. Nanoparticle-reinforced building materials with applications in civil engineering. Adv. Mech. Eng. 12(10), 1687814020965438 (2020).

Article Google Scholar

Golewski, G. L. Green concrete based on quaternary binders with significant reduced of CO2 emissions. Energies 14(15), 4558 (2021).

Article CAS Google Scholar

Golewski, G. L. An extensive investigations on fracture parameters of concretes based on quaternary binders (QBC) by means of the DIC technique. Constr. Build. Mater. 351, 128823 (2022).

Article CAS Google Scholar

Gil, D. M. & Golewski, G. L. Potential of siliceous fly ash and silica fume as a substitute for binder in cementitious concretes. InE3S Web of Conferences 2018 (Vol. 49, p. 00030). EDP Sciences.

Golewski, G. L. & Szostak, B. Strength and microstructure of composites with cement matrixes modified by fly ash and active seeds of CSH phase. Struct. Eng. Mech. 82(4), 543–556 (2022).

Google Scholar

Zou, F., Hu, C., Wang, F., Ruan, Y. & Hu, S. Enhancement of early-age strength of the high content fly ash blended cement paste by sodium sulfate and C-S–H seeds towards a greener binder. J. Clean. Prod. 244, 118566 (2020).

Article CAS Google Scholar

Ahmaruzzaman, M. A review on the utilization of fly ash. Prog. Energy Comb. Sci. 36(3), 327–363 (2010).

Article CAS Google Scholar

Pandey, V. C. & Singh, N. Impact of fly ash incorporation in soil systems. Agric. Ecosyst. Environ. 136(1–2), 16–27 (2010).

Article Google Scholar

Dermatas, D. & Meng, X. Utilization of fly ash for stabilization/solidification of heavy metal contaminated soils. Eng. Geol. 70, 377–394 (2003).

Article Google Scholar

PCA. Green in practice 102—concrete, cement, and CO2. Portland Cement Association; 2010.

Kalyoncu, R. S. & Olson, D. W. Coal combustion products. In: U.S. Department of the Interior, editor. Reston, VA: U.S. Geological Survey. 2001.

Adams, T. H. Marketing of Fly Ash Concrete (Michigan State University, 1988).

Google Scholar

Win, T. T., Wattanapornprom, R., Prasittisopin, L., Pansuk, W. & Pheinsusom, P. Investigation of fineness and calcium-oxide content in fly ash from ASEAN region on properties and durability of cement–fly Ash system. Eng. J. 26(5), 77–90 (2022).

Article CAS Google Scholar

Sereewatthanawut, I., Pansuk, W., Pheinsusom, P. & Prasittisopin, L. Chloride-induced corrosion of a galvanized steel-embedded calcium sulfoaluminate stucco system. J. Build. Eng. 44, 103376 (2021).

Article Google Scholar

Erdogdu, S., Arslanturk, C. & Kurbetci, S. Influence of fly ash and silica fume on the consistency retention and compressive strength of concrete subjected to prolonged agitating. Constr. Build. Mater. 25(3), 1277–1281 (2011).

Article Google Scholar

Prasittisopin, L. & Trejo, D. Effects of mixing variables on characteristics of blended cement systems containing rice husk ash. J. Mater. Civ. Eng. 2018;30(1).

Wang, S. Compressive strengths of mortar cubes from hydrated lime with cofired biomass fly ashes. Constr. Build. Mater. 50, 414–420 (2014).

Article Google Scholar

Yu, Z. & Ye, G. New perspective of service life prediction of fly ash concrete. Constr. Build. Mater. 48, 764–771 (2013).

Article Google Scholar

Prasittisopin, L. & Trejo, D. Characterization of chemical treatment method for rice husk ash cementing materials. ACI-Spec. Publ. 294, 1–14 (2013).

Google Scholar

Andersen, P. J. & Hodson, S. K. Concrete having high workability through control of fine-to-coarse particulates ratio. In: Teasdale A, editor. U.S.: iCrete; 2009. p. 28 pp.

Portland Cement Association. Survey of mineral admixtures and blended cements in ready mixed concrete. 2000. p. 16 pp.

Hooton, R. D. Bridging the gap between research and standards. Cem. Concr. Res. 38(2), 247–258 (2008).

Article CAS Google Scholar

Goñi, S., Lorenzo, M. P., Guerrero, A. & Hernández, M. S. Calcium hydroxide saturation factors in the pore solution of hydrated portland cement fly ash pastes. J. Am. Ceram. Soc. 79(4), 1041–1046 (1996).

Article Google Scholar

Lawrence, C. D. Changes in Composition of the Aqueous Phase During Hydration of Cement Pastes and Suspensions 378–391 (Highway Research Board, 1966).

Google Scholar

Fraay, A. L. A., Bijen, J. M. & de Haan, Y. M. The reaction of fly ash in concrete a critical examination. Cem. Concr. Res. 19(2), 235–246 (1989).

Article CAS Google Scholar

Prasittisopin, L. & Trejo, D. Hydration and phase formation of blended cementitious systems incorporating chemically transformed rice husk ash. Cem. Concr. Comp. 59, 100–106 (2015).

Article CAS Google Scholar

Park, B. & Choi, Y. C. Hydration and pore-structure characteristics of high-volume fly ash cement pastes. Constr. Build. Mater. 278, 122390 (2021).

Article CAS Google Scholar

Bentz, D. P. & Ferraris, C. F. Rheology and setting of high volume fly ash mixtures. Cem. Concr. Comp. 32, 265–270 (2010).

Article CAS Google Scholar

Paya, J., Monzo, J., Borrachero, M. V., Peris-Mora, E. & Gonzalez-Lopez, E. Mechanical treatment of fly ashes part II: Particle morphologies in ground fly ashes (GFA) and workability of GFA-cement mortars. Cem. Concr. Res. 26(2), 225–235 (1996).

Article CAS Google Scholar

Gopalan, M. K. Sorptivity of fly ash concretes. Cem. Concr. Res. 26(8), 1189–1197 (1996).

Article CAS Google Scholar

ACI Committee 226.3R-87. Use of fly ash in concrete Detroit: ACI; 1990.

Ramamurthy, K. & Harikrishnan, K. I. Influence of binders on properties of sintered fly ash aggregate. Cem Concr. Comp. 28(1), 33–38 (2006).

Article CAS Google Scholar

Langan, B. W., Weng, K. & Ward, M. A. Effect of silica fume and fly ash on heat of hydration of portland cement. Cem. Concr. Res. 32(7), 1045–1051 (2002).

Article CAS Google Scholar

Dewar, J. D. & Anderson, R. Manual of Ready Mixed Concrete 2nd edn. (Blackie Academic and Professional, 1992).

Google Scholar

Vieira, L. D., de Figueiredo, A. D., Moriggi, T. & John, V. M. Waste generation from the production of ready-mixed concrete. Waste Manag. 94, 146–152 (2019).

Article PubMed Google Scholar

Neville, A. M. Properties of Concrete 4th edn. (John Wiley & Sons, 1996).

Google Scholar

Brandt, A. M. Cement based composites: Materials, mechanical properties and performance. UK: E & FN Spon;1995.

Golewski, G. L. The role ofpozzolanic activity of siliceous fly ash in the formation of the structure of sustainable cementitious composites. Sustain. Chem. 3(4), 520–534 (2022).

Article CAS Google Scholar

Gong, Y. et al. A Kinetic study of the pozzolanic reaction of fly ash, CaO, and Na2O in the preparation of fly ash belite cement. Materials 12(20), 3303 (2019).

Article ADS CAS PubMed PubMed Central Google Scholar

Sabet, F. A., Libre, N. A. & Shekarchi, M. Mechanical and durability properties of self consolidating high performance concrete incorporating natural zeolite, silica fume and fly ash. Constr. Build. Mater. 44, 175–184 (2013).

Article Google Scholar

Download references

The authors wish to thank the school of Civil and Construction Engineering at Oregon State University and the Washington Department of Transportation for partial investigation of this study.

This research project was financially supported by Program Management Unit for Competitiveness Enhancement (PMU-C), Office of National Higher Education Science Research and Innovation Policy Council, Thailand and Thailand Science Research and Innovation Fund, Chulalongkorn University (SOC66250010).

Faculty of Engineering and Technology, Pathumthani University, Pathumthani, 12000, Thailand

Issara Sereewatthanawut

School of Engineering and Materials Science, Queen Mary University of London, London, E1 4NS, UK

Chinnapat Panwisawas

Department of Civil Engineering, Faculty of Engineering, Chulalongkorn University, Bangkok, 10330, Thailand

Chayut Ngamkhanong

Department of Architecture, Faculty of Architecture, Chulalongkorn University, Bangkok, 10330, Thailand

Lapyote Prasittisopin

You can also search for this author in PubMed Google Scholar

I.S.: Methodology, Investigation, Data curation. C.P.: Data curation, Writing - Review & Editing. C.N.: Resources, Writing - Review & Editing. W.P.: Supervision, Funding acquisition. L.P.: Conceptualization, Validation.

Correspondence to Lapyote Prasittisopin.

The authors declare no competing interests.

Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made. The images or other third party material in this article are included in the article's Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article's Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder. To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.

Reprints and Permissions

Sereewatthanawut, I., Panwisawas, C., Ngamkhanong, C. et al. Effects of extended mixing processes on fresh, hardened and durable properties of cement systems incorporating fly ash. Sci Rep 13, 6091 (2023). https://doi.org/10.1038/s41598-023-33312-x

Download citation

Received: 02 December 2022

Accepted: 11 April 2023

Published: 13 April 2023

DOI: https://doi.org/10.1038/s41598-023-33312-x

Anyone you share the following link with will be able to read this content:

Sorry, a shareable link is not currently available for this article.

Provided by the Springer Nature SharedIt content-sharing initiative

By submitting a comment you agree to abide by our Terms and Community Guidelines. If you find something abusive or that does not comply with our terms or guidelines please flag it as inappropriate.

Deep anoxic aquifers could act as sinks for uranium through microbial

Prem Shanker, CEO of Ramco Industries

News

Effects of extended mixing processes on fresh, hardened and durable properties of cement systems incorporating fly ash